IAG 600 FA20DI Built Short Block – 10.5:1 Compression – 2013-2020 Subaru BRZ, Scion FR-S & Toyota 86

$6,689.36

IAG Short Block Plug & Rear Main Seal Kit - FA20DI – 2013-2020 Subaru BRZ, Scion FR-S & Toyota 86

ARP Head Studs - 11mm Cylinder - 2015-2021 Subaru WRX, 2013-2020 BRZ, FR-S & 86

Fluidampr Harmonic Balancer - Subaru FA20 - 15-18 Subaru WRX, 19-21 WRX *WITH HUB* 13-20 BRZ, FR-S & 86

NOTE: IF YOUR CAR DOES NOT HAVE 12339AA010 HUB, THIS WILL NOT FIT. PLEASE CONTACT US.

Verus Engineering Bell Housing Cover - '13-'20 Scion FR-S, Subaru BRZ, Toyota 86, '15-'21 Subaru WRX - FA20

OEM Oil Filter 15208AA130 - Subaru BRZ, Scion FR-S, Toyota 86

OEM Oil Drain Plug Crush Washer - Most Subaru FA's & FB's

Motul Classic 10W40 Break-In Motor Oil - 1QT

Documents

Installation Instructions & Videos

SKU: IAG-ENG-S686L Category: Tags: , , Brand:

IAG 600 FA20 FT86/BRZ 2.0L SUBARU SHORT BLOCK WITH 10.5:1 LOW COMPRESSION

IAG Spec H-Beam FA20 Rods

DESIGNED FOR STRENGTH

The IAG 600 Short Block is designed for stock or modified FA20 Subaru BRZs that need a stronger short block to support increased cylinder pressures created by modifications, or aftermarket turbo kits. The IAG 600 short block features IAG Spec H-Beam forged connecting rods. The upgraded connecting rods and race bearings are able to support additional engine load produced by aftermarket turbochargers or increased boost which the OEM rods and pistons found in the stock short blocks cannot support reliably.

BUILT WITH 100% NEW COMPONENTS

Each IAG 600 Short Block starts with brand new FA20 BRZ/FT86 2.0L, 86mm stock bore engine case halves as standard. The case haves are carefullly bored and honed to 86.1mm then measured and assembled using a new 2015+ Subaru 2.0L FA20 crankshaft, which is matched to ACL or King race main bearings. The IAG 600 Short Block features IAG Spec H-Beam Connecting Rods with ARP2000 rod bolts, along with ACL or King race rod bearings. The case halves are sealed with new OEM main case bolts and sealant. Finally, IAG Spec JE FSR 86.1mm Forged Pistons are carefully selected, measured, and installed to finish off the short block.

FA20 Crank
FA Engine Case

MODIFIED OIL PASSAGES FOR INCREASED OILING

Adequate oil flow is critical to performance and relibility. It’s no secret that the OEM cases from Subaru leave something to be desired in the oiling department. Our machinists carefully inspect and modify the internal oil passages of each new OEM case used in the IAG 600 Short Block to ensure proper flow and reliability.

FORGED PISTONS, DESIGNED FOR BOOST

Each IAG 600 Short Block features IAG Spec JE FSR 86.1mm Forged Pistons. These 2618 T6 Alloy high-strength pistons have been specifically designed to support increased cylinder pressures which come with more boost. FSR forgings reduce mass and wear caused by friction without sacrificing strength. This is accomplished by using an asymmetrical skirt design instead of the traditional full-round skirt, also this reduces weight significantly. Featuring smooth flowing radii on the domes and dishes, the design promotes excellent flame travel. The pistons are secured to the rods with .905 x 2.250″ x .150″ wall carbon steel wrist pins with Tru Arc locks. Note this block features lower 10.5:1 compression ratio which is ideal for higher boost applications up to the power rating of the short block.

IAG Spec JE FSR Low Compression FA20 Pistons

IAG 600 FA20 2.0L FT86/BRZ Low Compression Short Block Includes:

  • Case Halves –Brand new OEM Subaru FA20 case halves, bored and honed to 86.1mm
  • Case Machining – Modified for improved oiling
  • Case Machining – Bored and honed to 86.1mm
  • Pistons –IAG-Spec 86.1mm Forged Pistons, Ring Set, and .150″ x 2.250″ Chromoly Wrist Pins. 10.5:1 Compression
  • Connecting Rods –IAG-Spec H-Beam / ARP2000 Rod Bolts
  • Rod –ACL or King XPG
  • Main Bearings –OEM or King XPG
  • Crankshaft –New Subaru FA20 crankshaft
  • Case / Main Bolts –Standard Subaru case bolts
  • Hardware – OEM Oil Plug – comes preinstalled at the oil pan location

Compression Ratio:

  • 10.5:1 compression on standard gasket thickness.

Power Rating:

  • The IAG 600 Short Block has a power output rating of 600 BHP

Additional information

Weight60.00 kg
Dimensions50.00 × 50.00 × 45.00 cm

Reviews

There are no reviews yet.

Be the first to review “IAG 600 FA20DI Built Short Block – 10.5:1 Compression – 2013-2020 Subaru BRZ, Scion FR-S & Toyota 86”

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Applications

Models suitable for this product

MakeModelYearSubmodel
MakeModelYearSubmodel
ScionFR-S2013 - 2016
SubaruBRZ2013 - 2016
SubaruBRZ2017 - 2018Performance Package
SubaruBRZ2017 - 2020Base
SubaruBRZ2018tS
SubaruBRZ2019Raiu Edition
SubaruBRZ2019 - 2020Sport-Tech
SubaruBRZ2019 - 2020Sport-Tech RS
SubaruBRZ2020tS
Toyota862017 - 2018
Toyota862019 - 2020Base
Toyota862019 - 2020GT
Toyota862019TRD SE
Toyota862020Hakone Edition

Got something to discuss?